Execution | Reliable Part Modelling 04

Tips & Tricks
Execution | Reliable Part Modelling in Autodesk Inventor 04

Click here to read part 03 of this series, in which we learned how to set up our environment for success, by adjusting our templates and application options and standardising our parameter and feature naming schemas.

In this post we will imaging that you are finally ready to start modelling…

Before you start STOP! Let’s take a few minutes to plan our model. What do we need to consider before Execution?

Tip: Click here to download the handout from class ‘Reliable Modelling Techniques for Complex Part Design in Inventor’ on Autodesk University online (It’s free) for a checklist to help you as you model.

Center Point

In cartesian coordinates, the Center Point (or Origin) is the 0,0,0 point of your model.

Modelling around the origin allows us to reference the Center Point as a fixed datum, around which our part can change in a predictable fashion.

The center point may be in a different spot for every item you model, but it should be something you think about before your start modelling.

‘Where do I want the origin to end up, when I’ve finished modelling this thing?’

Autodesk Inventor part model origin

Layout Sketches

If anything goes wrong with your Inventor model, it’s likely to go wrong with a sketch.

When you learned Inventor – you were probably given the advice:

‘One sketch per feature’

This advice is meant to guarantee simple sketches, which only contain one closed loop. When you edit the design, Inventor is unlikely to pick the wrong loop if there is only one choice!

The downside of this technique is that single feature sketches are unrelated, which means that Design Intent is not captured.

The other extreme is overly complex shared sketches which can be difficult to edit and difficult to diagnose when things go wrong.

A layout sketch could be thought of as a ‘Skeleton’ which contains the main datums for a component.

Feature sketches are related to the layout sketch with projected geometry. When the layout sketch is driven by a parameter change, the features sketches go with it.

All sketches should be fully constrained.

There – I said it. You can take it from me. Quote me on this:

‘Fully constrained means fully predictable’.

If you’re sketches aren’t fully constrained, you can’t predict behaviour when you edit your component.

Note the indicator in the bottom right of the sketch environment to see how close you are to being fully constrained.

You may also notice a ‘push pin’ icon on your sketch nodes in the browser. This is a great way to check to see if a sketch is fully constrained without having to open the sketch first.

If you don’t know what you need to do to fully constrain your sketch, use the degree of freedom indicator or the Auto-dimensioning tool to help.

Autodesk Inventor Layout Sketches

Datum Features

When we build a model by relating each sketch to the preceding feature, we can unintentionally build a house of cards.

When the Base Feature changes, all dependant sketches and features will also update. This can be extremely powerful (if this is what we intended) or extremely frustrating (when it isn’t).

Instead of basing a sketch on a feature, we can isolate the sketch from the preceding feature by basing the sketch on a datum plane. A datum plane can be a UCS, work plane or surface extrusion, which is driven by a named parameter or our layout sketch.

The link back to the layout sketch preserves Design Intent. The datum plane isolates the sketch from previous features, allowing us re-order the feature tree, or even delete features without upsetting our model.

Autodesk Inventor Datum Planes

Feature build order

This idea of grouping similar features comes from Dick Gebhard’s ‘Resilient modelling strategy’. When I trained students using this technique we found maintaining feature groups to be problematic – features must be in the right order to get the desired result!

However, working through Dick’s exercises with my students, we found building your model with feature order in mind works well and can lead to better structured, more stable components.

Tip: Although you create the features in the following order, this is not necessarily the order which they will end up in the feature tree. Use the ‘End of Part Marker’ (EOP) to place features in the position they need to be for your desired result.

Add >Modify >Remove >Pattern >Edges
ExtrudeDraftTrimMirrorChamfer
RevolveShellHolePatternFillet
ThickenThreadEmbossConcave before Convex
RibDelete faceBig Before small
Sweep
Loft
Coil

Autodesk Inventor reliable modelling technique feature types

Feature grouping

Autodesk Inventor Model Browser Features Grouped by Solid

When working on a multibody file, it can be helpful to group features together that belong to the same body.

Sadly, we don’t have folders or feature grouping for the model browser in the Inventor part environment.

Instead I use 3D sketches, which I name in ALL CAPS and then turn their visibility off. This gives me just enough of a visual cue to be able to skim up and down the browser efficiently.

Flex your design

Test your designs! If you have invested effort building a component which can change over time – don’t simply assume that your model will update predictably!

Don’t forget, it could be you who must perform a quick Friday afternoon update to a model. No-one wants to be dealing with an exploding model when they have a deadline to meet.

I’ve stolen a term from Revit designers here, they call this testing ‘Flexing’ the model.

Flex early, flex often, flush any unpredictable behaviour out of your design while the design intent is fresh in your memory.

It’s far more difficult to correct mistakes when you are revisiting a component after a few months working on other projects.

Communicating design intent

Well done for making it this far! Only one more post to go 😉

Now you have built a reliable, parametric Inventor part model, how are you going to prevent you colleagues from messing it up!?

The answer is with good documentation. Before your model is complete, you need to spend some time communicating your design intent through good documentation – and that’s what we will discuss next…

 

 

 

Documentation | Reliable Part Modelling 05

Click on this link to read part 05 in this series and learn how to communicate all the hard work you put into your design intent to your colleagues.

This blog post is based on an Autodesk University class, by Luke Mihelcic and Paul Munford. You can watch a recording of the class, and download a handout that goes with this presentation from the Autodesk University website here:
MFG226705: Reliable Part Modeling Techniques for Complex Part Design in Inventor

Edit 2020/11/24 

This class was updated and repeated for Autodesk University 2020. You can find the revised version of the class, with video, handout, and dataset here:
‘Reliable Modeling Techniques for Complex Part Design in Inventor’ At AU2020

We also created a second part to the class: ‘Reliable Techniques for Complex Assembly Design in Inventor‘ – Here’s the link:
‘Reliable Techniques for Complex Assembly Design in Inventor’ at AU2020

Paul Munford Autodesk Inventor subject matter expert (Geek!).



Paul Munford

Paul Munford is a laugher, dreamer, raconteur, CAD geek and Industry Marketing Manager for Autodesk in the UK. Paul's background in manufacturing items for the construction industry gives him a foot in digital prototyping and a foot in Building Information Modeling (BIM). Paul was a speaker at Autodesk University for the first time in 2012, and he says it's the most fun anyone can have with 250 other people in the room.

2 comments

  1. msetrakian

    Hi Paul, thanks for this great series. Can you share some techniques for “flexing” the model? I do it by reordering features and updating, but there may be other/better ways.

    1. Paul Munford
      Paul Munford

      Hi Mark, You got it! If you've designed a component to change when you change the value of a parameter, don't assume that it's going to work! Change the value of the parameter and see what happens. There's nothing worse than coming into work on a Monday, updating a model I made last week - watching it break and then not being able to remember my thought process when I was building it :/ This is what I mean by 'Flex' (It's a term I borrowed from our Revit colleagues). Let me know if that helps? Paul

Add comment